-
496bf84f 9ad4 47d0 8880 2bcb6f9d3d8c

invention

Cardboard Box Mars Rover

by echothebat

Published on October 15, 2015

This Rover is remotely triggered by any household remote control. It uses one motor and is the Rover project that is detailed in the Space Kit booklet. You should be able to make this assorted materials around the house.

Duration: 3 hours

Credits: Original concept by littleBits' Emily Tuteur for the Space Kit with additions from Chris and Ginger Butcher.

How To Make It

STEP 1 : Construct the drive wheel

F1ed08c4 246b 4b62 9d30 22832c858436

Cup rims taped together can form the base of your wheel. Add cardboard circles to each side to complete the wheel.

E7e60bb6 52a6 4ca9 be22 58c70433c230

This example uses a cardboard ribbon spool with rubber bands for traction. TIP: Glue short craft sticks at center for added support.

To make the big wheel, cut the tops off of two plastic cups. Slide them together, rims facing out. Tape them together. Then glue cardboard circles to each side. 

ALTERNATE - other items that can be used for a drive wheel include a card board ribbon spool, styrofoam cups, section of a round oatmeal container, or other cylinder that is about 3" - 4" in diameter and at least an inch or two thick. 

STEP 2 : Set up box

7094b322 2a50 4e41 8e52 e64233e81bdd

On your medium sized box, mark the size of your wheel.

A82ec32c b027 4178 98cb d37f0a758fb8

Then cut opening for your wheel.

Make a hole in the base of the box large enough to fit your wheel. This will be the bottom of your Rover.

STEP 3 : Make the axle

B0eecad5 432d 4334 bf62 7f53deadbebd

Put craft stick through the sides of the wheel and cut one end so it is straight - keep the other side of the stick rounded.

Cut slots in the side of your wheel large enough for the craft stick. Then put the craft stick through the slots and cut one end so it is has a straight edge to attach to the motor mate. 

TIP: Since this is the drive wheel, add something like rubber bands for added traction.

STEP 4 : Make an axle holder

34688a7a 579e 4e4f 8488 ee53f6145d3c

For axle mount, fold a piece of corrugated cardboard so that is stands up with tabs that can be glued or taped in place.

9ed59100 8b88 41fa bf8c 808bd3460c33

Cut a hole the size of your craft stick - but only on ONE side of the axle mount so the stick won't poke through. Tape or glue axle mount next to the hole for the wheel.

To make an axle holder for the craft stick on your wheel, cut a strip of cardboard and fold it like a tent (see photo). Make a hole in one side of the tent that is the size of the tip of the craft stick. Tape your axel holder down next to the hole you made for the wheel in your box. 

STEP 5 : Attach your wheel

9504e146 5294 4e09 af22 d8513877b583

Mount the motor in your box - use shoes or cardboard to raise it up a little - and attach to craft stick with MotorMate.

51c76f2d 2c08 4859 b3b1 9cd9d535a11e

Attach the other end of the craft stick in the hole of the axle mount. You may need to adjust the size of the craft stick to fit.

Mount the motor on the other side of the wheel opening - across from the axle holder. Set the wheel in place with one side of craft stick attaching to the motorMate and DC motor. The other end of the craft stick sets in the hole of the the axle holder. You may have to cut the craft stick to fit. 

STEP 6 : Build the outside wheels

D54ad9ca 3f0f 470f 869c 048e90678f29

Cut six pieces of paper tube (about 1-2 inches in width).

36646598 083e 42b7 9555 45f2c32dd36a

Cut six circles of cardboard and glue inside each of the paper tubes.

Cut a paper tube into six pieces to create wheels about 1-2 inches wide. Cut six cardboard circles to fit inside the wheels. Using a skewer, poke holes in the center of each circle. Place a cardboard circle in each paper tube and glue in place. 

STEP 7 : Attach the outside wheels

A154a282 6a72 4001 9111 4b783d2bc386

Use the skewers or chop sticks to attach the wheels to each side of the box. Note the drive wheel should be lower than the small outside wheels.

Make three holes in opposite sides of the box for axles. Poke skewers through a hole in one side of the box and out through the hole on the opposite side. Glue wheels on the end of the skewers. Special Note: The two middle wheels are just glued in with short axles because a longer axle would interfere with the center drive wheel. These middle wheels won't spin.

STEP 8 : Connect your circuit

285b3119 7712 4c71 9248 d14db8a3e2e7

Connect the bits to form the circuit -- Power + IR Trigger + Wire + Motor + Wire + Light Sensor + Number.

Bfa2e12d e642 43fd 913f 39732716ce1d

Make sure that all the wires are out of the way of the center drive wheel inside the box.

Connect wires to the motor inside the box and then connect the rest of the bits (see photo of circuit). The Power, IR, and Motor can all be inside the box. The Light Sensor and Number bits will be outside the box.

STEP 9 : Add the Rover instrument

A749b873 b528 429e b887 7259cf696807

Stick a small box on top of the craft stick or pencil and hot glue in place. Tape the light sensor and number modules to the front of the small box.

Rovers carry scientific instruments to take measurements and send data back to Earth. This instrument is an energy sensor. It will sense the amount of light and display data on the number bit.

To add the instrument, put a craft stick or pencil vertically through the top of the cardboard box near the front. (Be sure not to get in the way of the center drive wheel inside). Stick a small box on top of the craft stick and hot glue in place. Tape the light sensor and number modules to the front of the small box. Cut a small hole in your box so you can access the power switch.

STEP 10 : Decorate your box

578136d5 d905 49c9 a943 60c203bac0cc

Decorate and control your rover using any household remote. The trigger will turn the motor on driving the center wheel. You are ready to drive on Mars!

2853148a 5d32 4eca b2a2 e65e90cce345

Try different materials like the bottoms of soda cans for the wheels to create a techy-look.

Get creative! Add stickers. Paint. Cover with foil for a high-tech space look. Then take your rover for a drive using any household remote control. 

Related Projects

Spooky spider and the possessed pumpkin scream machine #HackHalloween

This is a #HackHalloween special that includes a remotely controlled spider that blinks and buzzes and a possessed ...

Giraffie and Hedgie go on a voyage

As part of #InventAnything Basic track, I made a Travel Tale of two friends - Hedgie and Giraffie - crossing the Atlantic to visit...

#SNAPTOIT Pantry Alarm

The alarm goes off when the light is turned on.